在近幾年的電氣設計以及施工現場配合工作中，搞過一些封閉式母線槽線路的設計。下面就由濟南電纜橋架廠家為我們講講有關內容吧。

In recent years, in the electrical design and construction site cooperation work, I have done some design of enclosed bus duct lines. Now let's talk about the relevant contents from Jinan cable bridge manufacturer.

盡管封閉式母線槽有很多優點，但在實際應用中也受一定條件的限制，如用電負荷類型、分布情況，安裝空間，工程投資額度等等。

Although the enclosed bus duct has many advantages, it is also limited by certain conditions in practical application, such as the type of power load, distribution, installation space, project investment amount and so on.

封閉式母線槽在高層建筑里的應用一般建筑都會為封閉式母線槽設計安裝空間(豎井)，每個樓層均設一個或多個插接開關箱，再由插接開關箱向各用電設備及回路以電纜、電線方式送出電源。為了用電安全，設計時應注意以下幾點：

The application of enclosed bus duct in high-rise buildings generally, the construction profession will design the installation space (shaft) for the enclosed bus duct. Each floor is equipped with one or more plug-in switch boxes, and then the plug-in switch boxes send power to all electrical equipment and circuits in the form of cables and wires. In order to use electricity safely, the following points should be paid attention to in the design:

為了保證供電線路的連續性，應考慮采用雙回路形式，并盡可能使兩回路有一定的安全間隔；在選擇封閉式母線槽規格時，導體截面應盡量大一些，以保證具有足夠的剩余容量；要多設插接口，但要考慮到操作高度和動力饋線路徑，因?yàn)榇怪辈贾玫姆忾]式母線槽插口過多會使每層上面的插接箱高度過高，操作和檢修都不方便；

In order to ensure the continuity of the power supply line, the double circuit form should be considered, and there should be a certain safety interval between the two circuits as far as possible; When selecting the specification of enclosed bus duct, the conductor section should be as large as possible to ensure sufficient residual capacity; More sockets should be set, but the operation height and power feeder path should be considered, because too many sockets of vertically arranged enclosed bus duct will make the height of the socket box on each floor too high, which is inconvenient for operation and maintenance;

由于封閉式母線槽線路阻抗很小，在選擇插接箱內斷路器時應選短路分?jǐn)嗄芰εc之相配的型號；對于垂直安裝于剪力墻上的封閉式母線槽，可不必向建筑設計人員提供載荷數據。對于垂直穿樓板安裝的封閉式母線槽，其載荷數據應按如下公式計算：支撐點載荷=0.5×建筑層高×(母線槽總重/母線槽總長)。由于封閉式母線槽結構比電纜橋架重得多，應建議設計人員考慮吊裝空間。

Because the impedance of enclosed bus duct is very small, the model with matching short-circuit breaking capacity should be selected when selecting the circuit breaker in the plug-in box; For enclosed bus ducts installed vertically on shear walls, it is not necessary to provide load data to building designers. For the enclosed bus duct installed vertically through the floor, the load data shall be calculated according to the following formula: load at the support point =0.5 × Building floor height × (total weight of bus duct / total length of bus duct). Since the enclosed bus duct structure is much heavier than the cable tray, it is suggested that the designer consider the hoisting space.

封閉式母線槽在大型生產、加工車間內的應用對于單機負荷較小、分布均勻的大型廠房，如紡織企業的織布車間、針織車間，機械加工企業的小件加工車間等，可以利用封閉式母線槽、插接箱的組合進行供電。在這種場合封閉式母線槽與常規供電方式(電纜供電)相比，其優越性為：

The application of enclosed bus duct in large-scale production and processing workshops for large-scale workshops with small single machine load and uniform distribution, such as the weaving workshop and knitting workshop of textile enterprises and the small piece processing workshop of mechanical processing enterprises, the combination of enclosed bus duct and plug-in box can be used for power supply. In this case, compared with the conventional power supply mode (cable power supply), the advantages of closed bus duct are:

對用電負荷的均衡分布性要求不高，因此對負荷很不均衡的情況適應性強。即使在封閉式母線槽線路已經完成設計或已安裝完畢的情況下，也可以根據新的負荷變動方案進行簡單的調整，這一點常規供電方式(電纜供電)是無法與之相比的。另外，價格低廉的插接箱取代了昂貴的低壓配電柜及動力箱，可以降低投資。同時插接箱內動力開關更接近用電設備，停、送電操作非常簡便。

The requirement for the balanced distribution of power load is not high, so it has strong adaptability to the situation that the load is very unbalanced. Even if the enclosed bus duct line has been designed or installed, it can be simply adjusted according to the new load change scheme, which cannot be compared with the conventional power supply mode (cable power supply). In addition, the low-cost plug-in box replaces the expensive low-voltage distribution cabinet and power box, which can reduce the investment. At the same time, the power switch in the plug-in box is closer to the electrical equipment, and the operation of power stop and transmission is very simple.

在設計選型時應根據系統的短路電流值及樣本上的參數對所選定型號進行動穩定和熱穩定校驗或計算，詳情就來我們網站http://www.ymmgjx.net咨詢看看吧。

During design and model selection, the dynamic stability and thermal stability of the selected model should be verified or calculated according to the short-circuit current value of the system and the parameters on the sample. For details, please visit our website http://www.ymmgjx.net Consult and have a look.